Standing Seam Metal Roofing in Savannah

Savannah sits on a low sandy bluff above the Savannah River, ringed by tidal marsh and creeks, under live oaks draped in Spanish moss. That setting is beautiful, but it is hard on roofs. Salt-laden humid air, intense UV through long summers, and violent afternoon thunderstorms with straight-line wind and occasional hail punish every roof on the Historic District, the Victorian District, Ardsley Park, and out across Pooler and Richmond Hill. Standing Seam Metal Roofing in Savannah is the system we install most for homeowners who want a roof that outlasts the weather and looks right on everything from a Greek Revival townhouse to a raised Lowcountry cottage on the Isle of Hope. Concealed fasteners mean no exposed screws for salt air to attack or heat cycles to loosen. If you are weighing this against a screw-down panel, start with our metal roof installation overview, then compare profiles below.

Why Standing Seam Holds Up to Chatham County Weather

The failure mode that dominates here is not snow load or ice damming. It is wind-driven rain and heat cycling. Hurricane and tropical-storm gusts push water sideways into every seam and penetration, and repeated expansion and contraction works loose anything that relies on a gasket. Standing seam panels are roll-formed to length and mechanically seamed or snap-locked, so the roof moves as one continuous skin instead of thousands of individual fasteners.

• We roll-form panels to the exact length of each run, which eliminates lap seams where wind-driven rain can enter.
• We set concealed clips that allow the panel to expand and contract without backing out a single screw.
• We specify a cool reflective finish that cuts attic heat gain through July and August.
• We install high-wind-rated panels that meet uplift requirements for hurricane season along the coast.
• We detail every valley, ridge, and penetration so oak and pine debris cannot dam water against the panel.

That combination is why standing seam carries a higher upfront price than exposed-fastener panels and still wins on lifecycle cost for most Savannah homes.

Key info: On Tybee Island and Wilmington Island, salt air eats exposed screws and washers faster than anywhere inland. A concealed-fastener standing seam roof removes that failure point entirely, which matters on raised cottages with deep porches where the roof is fully exposed to onshore wind.

Before you commit, check the wind and product standards published by the Florida Building Code product approval system, which many coastal manufacturers use to document uplift ratings, and confirm with the City of Savannah building department what your property requires.

How We Install Standing Seam on a Savannah Roof

Every job starts with the roof deck, not the panel. On 1880s wood-frame Victorians in Thomas Square and 1920s Craftsman bungalows around Forsyth Park, we often find skipped sheathing and soft decking under the old roof. We correct that before a single panel is formed. On newer stucco-and-siding homes in Pooler and Port Wentworth, the deck is usually sound and the work moves faster.

1. We inspect the deck, framing, and attic ventilation, and we replace any soft sheathing we find.
2. We install underlayment and ice-and-water protection at valleys, eaves, and penetrations.
3. We roll-form panels on site to the measured length of each run.
4. We set concealed clips and seam or snap-lock the panels according to the manufacturer's wind rating.
5. We fabricate and install ridge, hip, valley, and eave trim that matches the panel profile.
6. We seal and flash chimneys, skylights, and vent stacks, then clean the site and walk the roof with you.

Each step is documented with photos so you know exactly what is under the panel before we close it up.

Key info: On a 1920s bungalow in Ardsley Park, we found the original 1x sheathing had been skipped in two bays. We re-decked those sections and added ventilation before rolling panels. Skipping that step is how a premium roof fails early. If your home is in the 31401 ZIP, see our Savannah 31401 standing seam page for local details.

Standing Seam Profiles and Seaming Methods We Install

Not every Savannah roof wants the same panel. Historic district design review may restrict profile height and color, while a barn or shop in Effingham County can take a wider, more utilitarian panel. We match the panel to the house and to the wind zone it sits in.

We confirm which profile your home can take before you sign anything, including any historic or HOA review.

Standing Seam Metal Roofing Cost in Savannah: What to Expect

Standing seam pricing starts at From $10 per square foot installed, and most Savannah homes land above that figure once you account for tear-off, deck repair, and trim. A simple gable on a 2000s subdivision home in Pooler sits near the low end. A steep Victorian gable, a complex hipped roof, or a home with multiple valleys and dormers pushes toward the high end.

The biggest cost drivers are roof complexity, panel gauge and finish, deck condition, and access. A house on a narrow lane in the Historic District where we cannot stage a dumpster close to the roof costs more to work than a wide-open lot in Richmond Hill. Color and finish matter too: a premium cool-reflective paint system adds cost but reduces summer heat gain.

Get two or three estimates and compare scope, not just the number. One bid may skip deck repair or use a thinner gauge. Our full pricing overview breaks down what each tier includes so you can compare apples to apples.

Standing Seam Metal Roofing Near Me: How to Vet a Contractor Near Savannah

Hiring a metal roofing contractor near Savannah is not the same as hiring a shingle crew. Standing seam requires a roll-former, seaming tools, and crews who understand clip spacing and thermal movement. Ask direct questions and expect direct answers.

• Confirm the contractor is licensed and insured, and ask for a certificate of insurance naming you as certificate holder.
• Ask for references from standing seam jobs in Savannah, Pooler, or Richmond Hill, not just shingle roofs.
• Confirm who pulls the roofing permit with the City of Savannah or Chatham County, and that inspections are included.
• Ask how they handle historic district or HOA design review before any material is ordered.
• Get the panel gauge, finish warranty, and wind rating in writing on the estimate.

If a contractor cannot answer these questions plainly, keep looking. You can request a free estimate and we will walk your roof and put the scope in writing.

Standing seam is the last roof many Savannah homeowners buy, so it pays to get the deck, the profile, and the crew right the first time. Call (912) 468-1649 to schedule an inspection.

Standing Seam Metal Roofing in Savannah: Pricing Guide

Indicative pricing, the exact cost depends on square footage, finish, and site access. Free personalized estimate within 24h at (912) 468-1649.